Braeburn 2030 Thermostat Operation Manual

The Braeburn 2030 is an economy programmable thermostat designed for 1 heat/1 cool conventional or heat pump systems. It features a large backlit display, SpeedSet programming, HOLD function, filter monitor, and adaptive recovery mode, ideal for residential applications. Below are the key specifications and operation instructions.

1. Key Specifications 2. Operation Instructions 2.1. Initial Setup 2.2. Operating the Thermostat 2.3. Temperature Display Adjustment 2.4. Troubleshooting 3. Installation Instructions 3.1. Remove Old Thermostat 3.2. Installing New Thermostat 3.3. Battery Location 3.4. Power Options

Key Specifications

Type: Programmable Thermostat for 1H/1C Conventional or Heat Pump Systems
Compatibility:
- Single stage conventional and heat pump systems
- 250-750 millivolt heating only systems
- 2 wire hydronic zone systems
- Not compatible with multi-stage systems beyond 1H/1C
Power Source:
- Hardwired: 18-30 VAC
- Battery: 2 AA Alkaline batteries
Electrical Rating:
- 1 amp maximum per terminal
- DC Power: 3.0 Volt DC
Display: 4.4 sq in Backlit LCD with large characters
Operating Conditions:
- Control Range: 45°F to 90°F (7°C to 32°C)
- Accuracy: +/-1°F (+/-0.5°C)
- Humidity: 5% to 95% RH
Dimensions: Approximately 3.7” H x 5.2” W x 1.4” D
Features:
- 7-day, 5-2 day, or non-programmable modes
- SpeedSet programming
- HOLD function for program override
- User selectable filter monitor
- Adaptive Recovery Mode (ARM)
- Compressor short cycle protection
- Low battery indicator
- Built-in installer settings menu
Configuration Options:
- Programming Mode: 7-day, 5-2 day, NONE
- Temperature Scale: °F or °C
- 1st Stage Differential: 0.5°, 1°, 2°
- Compressor Short Cycle Protection: 0-5 minutes
- Adaptive Recovery: ON/OFF
- Filter Check Monitor: OFF, 30-365 days
- Extended Hold Period: LONG or 24 HR
- Temporary Override Adjustment Limit: +/- 0-3°
- Security Level: 0-3

Operation Instructions

Initial Setup

1. Turn Off Power: Always turn off power to the heating/air conditioning system prior to installing or adjusting the thermostat.
2. Configure System:

Hold MENU for 5 seconds to enter installer settings.
Use NEXT (HOLD) to advance, BACK (PROG) to go back, up/down arrows to change values.
Set options like PROG MODE, DEG, DIF1, CSCP, REC, FILTER, HOLD, OVERRIDE, SEC.
Exit with MENU.

Operating the Thermostat

1. System Mode: Select COOL, OFF, HEAT using the SYSTEM switch.
2. Fan Mode: AUTO or ON using the FAN switch.
3. Temperature Setpoint: Use up/down arrows to adjust; OVERRIDE for temporary, HOLD for extended override.
4. Programming: Press PROG to enter, select day/group, set time and temperature for MORN, DAY, EVE, NITE events. Use SpeedSet by holding PROG for 3 seconds.
5. Display: Shows current time, temperature, program event, system status (HEAT ON, COOL ON), fan status, SERVICE FILTER.
Note: Adaptive Recovery starts system early to reach setpoint by program time. Compressor protection delays restart.

Temperature Display Adjustment

Configure temperature scale (°F/°C) in installer settings under DEG. No direct calibration; accuracy is +/-1°F. Use separate thermometer for verification if needed.

Troubleshooting

No Display: Check batteries or 24V power, polarity.
No Heat/Cool: Verify system mode, setpoint, wiring, short cycle delay.
Fan Constant: Check fan mode, wiring.
Erratic Operation: Check voltage, batteries, reset by removing batteries/power for 2 minutes.
Low Battery: Battery symbol appears; replace batteries.
Service Filter: Reminder after set days; reset in user settings.
CHECK Indicator: System issue; contact technician.
Reset: Remove batteries/power for 2 minutes to reset.

Installation Instructions

Warning: Turn off power before installation. For experienced technicians only. Use only with compatible systems; conform to local codes. Provide disconnect and overload protection.

Remove Old Thermostat

Turn off power. Disconnect wiring, note connections. Remove old mounting hardware and thermostat.

Installing New Thermostat

Mount sub-base level on wall, approximately 5 ft above floor, avoiding drafts/sunlight. Drill holes, secure with screws/anchors.
Connect wiring: Rc/Rh (jumper for single transformer), W1, Y1, G, O/B, C (common). Set factory switch to CONV/HP and HG/HE.
Insert batteries if using battery power.
Configure installer settings.
Snap thermostat body onto sub-base.
Apply power, test system.

Battery Location

Batteries are located in the rear housing of the thermostat body. Remove body from sub-base, replace 2 AA alkaline batteries ensuring correct polarity.

Power Options

Hardwired with 24 VAC or battery powered.

Power Method	Description
Hardwired	Runs on 18-30 VAC from system transformer, with optional battery backup.
Battery	Runs on 2 AA alkaline batteries; low battery indicator provided.

Caution: Use alkaline batteries only. For dual transformers, common from cooling side. Do not short terminals.